First mistake I made is I used lead free solder with silver bearing rosin core. After completing steps up to page 23, I attempted to "Clip the black lead of your Digital MultiMeter to N on the IEC inlet. Clip the red lead of your DMM to L on the IEC inlet.", but when I measured the voltage, I was only getting 1.2V with the custom power cord and 5.2V with the provided stock power cable. I felt like my solder connections were solid so I likely made mistake #2 when I continued the assembly from the "if voltage is less than 115V" (which mine certainly was) I followed all of the steps for that section and on page 29 I re-ran the test and now get 7.2V with the standard power cable so it did increase, but not by much. When I ran the Secondary Power Transformer test using terminal seven and terminal 9, I get zero voltage and it doesn't change if I turn the switch on or off for this check. I'll include some pictures, but if someone could help me, I'm stuck right now and not sure what to do next. Could it be my solder in which case I need to take it all apart back to the beginning? I'll wait to hear back from someone before going down that road. I have a link to some pictures I took, but this forum is not letting me share external links. Is there any other way for me to share some of the pics I have taken?
Help! Mistakes were made...Assembly of Crack Amp Kit [resolved]
- Thread starter zaramon
- Start date
Can you clip your meter onto the amp as directed on page 23 of the manual and upload a picture of your measurement?
Is the fuse installed? In the correct position?
I would definitely throw away the solder that you have and get some leaded solder. The lead free stuff isn't going to hurt anything, but it's very difficult to work with.
Is the fuse installed? In the correct position?
I would definitely throw away the solder that you have and get some leaded solder. The lead free stuff isn't going to hurt anything, but it's very difficult to work with.
Good afternoon and thank you for your assistance. The fuse is installed correctly as best I can tell it doesn't matter which direction the tube ends face and they are making contact to the connectors in the bottom of the switch. How can I share images with you? The forum doesn't want to allow my external URL. I have pictures of the requested voltage test. Can you piece this together? h++ps://photos.app.goo.gl/KsWtm6FV6TRumb2y9
The last picture with the DMM is the one requested I believe.
The last picture with the DMM is the one requested I believe.
OK, it's good to see that your meter is setup correctly. If you shove the probes into your wall socket, do you see 120V? How about if you shove the probes into the power cord?
The fuse goes into the clip on the holder, not the square tunnel, and it's somewhat common for this to give you 0V at those terminals.
Either way, getting wall outlet and power cord readings will be helpful.
The fuse goes into the clip on the holder, not the square tunnel, and it's somewhat common for this to give you 0V at those terminals.
Either way, getting wall outlet and power cord readings will be helpful.
Leave one meter clamp on the N terminal of the IEC power entry module, then touch the other probe to the metal bar across from the L and N terminals and let us know what AC voltage you see there.
I uploaded a few more pics, my voltage is still very low when connecting the N + L terminals, only getting a little over 3V which is slightly less than earlier today. One thing I did notice, does the orientation of the power switch matter? The instructions say to mount with the . or 1 side closest to the chassis, so that is what I did, however, moving the switch to the side with the o on it is powering the device on. Does that sound fine? I uploaded a pic of the power button called powerbutton.jpg on the same share from the previous message.
Paul Birkeland said:
In your pictures this area of metal actually says L by it.
There is no concern about the power switch at this juncture since you aren't getting your incoming AC line voltage, so don't worry about that just yet.
Ok, I see what you meant, I misunderstood. Please see the most recent 2 pictures on the share I posted previously. One pic shows without the second lead touching the bar @ ~ 2.5V and second pic shows the second lead touching the metal bar across from the N + L terminal showing ~ 3.0V, so just a slight amount higher. Any thoughts?
Can you retake that measurement but slip the clamps off the meter and just use the poky probes?
I would try a different power cord. These are commonly found on things like printers, monitors, etc. This could just be a pin fitment issue with the current cord.
Again, it's not the switch, nor is it the fuse. You can pull the switch out and toss it to the side and it won't make any difference to the incoming voltage and the fuse is after the metal strip across from the two solder lugs. The power cord has a hot and a neutral connection that carry the incoming line voltage, and those mate up to two poky bits inside the IEC receptacle, and that is what we are attempting to measure.
What I would do next is to leave the power cord plugged into the amp but pull it from the wall. Set your meter to DC resistance and put one probe on one of the flat metal pins on the power cord that plugs into the wall, then touch L and N with the other meter probe to see if you get a 0 ohm reading, then repeat that for the other metal pin. You should get 0 ohms between each flat pin on the power cord and one of the metal bits on the IEC power entry module.
What I would do next is to leave the power cord plugged into the amp but pull it from the wall. Set your meter to DC resistance and put one probe on one of the flat metal pins on the power cord that plugs into the wall, then touch L and N with the other meter probe to see if you get a 0 ohm reading, then repeat that for the other metal pin. You should get 0 ohms between each flat pin on the power cord and one of the metal bits on the IEC power entry module.
What you're describing is an impossible set of circumstances. If you have 0 ohms between both flat blades of the power cord and a corresponding terminal on the IEC power entry module, then your AC line voltage will make it through.
Ok, my apologies for being new to using a digital multimeter, but I have a bachelor's degree in computer science with over 24 years of industry experience so I know I can follow directions well so please don't give up on me. Here's what I have this time, when clipping on one flat blade of the power cord and touching terminal L, the meter reads ~ 7.8 and when touching terminal N it reads ~0.1. Switching to the other flat plug of the power cord I get 0L when touching terminal L and 0L when touching terminal N. Please let me know if I'm making any additional mistakes. I have uploaded 4 more pictures to show these results with a clear view of the DMM in case my settings are incorrect. Thank you again for your patience and help. Again, the photos can be accessed by replacing the two '++' characters with 'tt' in the URL h++ps://photos.app.goo.gl/KsWtm6FV6TRumb2y9 to have a working URL to get around the forum blocking external URL's (sorry if I'm breaking any rules here).
Thermioniclife
Member
Do you have your meter set to AC volts?
Similar threads
