Crack Help [solved]

[russell_janab]

Terminal Resistance in Ohms
13 -704K
B3 3.6K
B6 3.6k

Center pin red 104.1K Ohms
Center pin black 97.1K Ohms

Terminal Voltage in Volts
1 -0.93
2 -0.94
3 0
4 -0.24
5 -0.93
6 0
7 0
8 0
9 2 mV
10 0
11 0
12 0
13 -0.95
14 0
15 241
20 0
21 240
A1 -0.93
A2 0
A4 0
A5 0
A6 -0.93
A7 0
A9 0

The 2 red LEDs are not lighting up.

Thanks in advance,

Sam Janab

 

[Paul Birkeland]

Hello Russell,

If you let us know which kit you have, I can split this post off into its own topic on the board for that kit.

-PB

 

[russell_janab]

Hey PB,
I have the Crack Bottlhead OTL stock kit (Speed ball on the way )

Thanks in advance,

Sam Janab

 

[Paul Birkeland]

Hello Sam,

Did you install the fuse in your Crack?

-PB

 

[russell_janab]

Hey PB,
Yes I did

 

[Paul Birkeland]

There is a 270 Ohm 5W resistor between T13 and T15, it is likely disconnected on one end, as there is voltage on one side of it, but not the other.

If this resistor is well connected, and your voltages are correct, that resistor is going to get very hot during testing, and that piece of information will be useful.

-PB

 

[russell_janab]

Hey PB,
Yeah I measured that and for T13 I got - 704KOhms and 0 Ohms for T14

 

[Paul Birkeland]

I'm speaking of voltages.  You have 241V on one side of that resistor and 0 on the other.  Either one end is disconnected, one end is wired to ground, or there was a measurement error.

-PB

 

[russell_janab]

Hey PB,
you were right T13L was not soldered, tricky place.
I soldered it and now I am getting a resistance of infinity. Do you think the resistor is damaged or not soldered properly?

 

[Paul Birkeland]

Since you have already done the voltage checks, you should repeat them again.

-PB

 

[russell_janab]

hey PB,
Here are the new readings, everything is consistent with the manual except resistance at T13
i am getting infinity where as the manual indicates 270K Ohms


Terminal Resistance in Ohms
1 *
2 *
3 0
4 *
5 *
6 2.4K
7 2.9K
8 0
9 2.9K
10 2.4K
12 0
13 infinity
14 0
20 0
22 0
B3 3.6K
B6 3.6k

Center pin red 104.1K Ohms
Center pin black 97.1K Ohms

Terminal Voltage in Volts
1 82
2 172.5
3 0
4 172.5
5 80
6 0
7 105
8 0
9 104
10 0
11 0
12 0
13 172.5
14 0
15 194
20 0
21 215
A1 79
A2 0
A4 0
A5 0
A6 81
A7 0
A9 0

b1 81
b2 172
b3 104
b4 79
b5 172
b6 104
b7 0
b8 0



What Should I do?

 

[russell_janab]

nevermind PB,
It works beautifully I am speechless at its performance with HD 650's

Cheers!

 

[Paul Birkeland]

Enjoy those tunes!

-PB